Contact RCM Flow Meter Sales Department: 1+201-419-6111 or sales@nciweb.com


RCM Industries liquid Flow Meters

RCM Digital FlowmeterThe New digital display flow meter is a 2 wire loop powered 4-20mA DC indicator that displays a flow rate and total. On-screen engineering units are easily configured. Password protection and 16 bit A/D resolution. A New built in wet/wet differential pressure sensor is protected by an isolated stainless steel diaphragm and provides a 4-20mA DC signal to the display. The enclosure is IP67 / NEMA 4X rated which further enhances this models capability. Available in threaded or flanged connection and bronze or stainless steel construction.

The RCM Flo-Gage is a direct reading liquid flowmeter and gas flowmeter with a large easy to read dial calibrated in engineering units (GPM, SCFM, LPM, etc.). The Flo-Gage is suitable for measuring water, oil, and most low viscosity liquids as well as compressed air, oxygen, carbon dioxide, nitrogen and many other non-toxic compressed gases. Saturated steam can also be measured up to 120 psig max. The flowmeter is self contained and complete. Available in threaded and flanged connection.

Liquid meters are suitable for potable and non-potable water, irrigation water, glycol-water mixtures, fuel oils, lubricating oils, gasoline and many other low and medium viscosity liquids (maximum viscosity 500 centipoise).
Click to openFeatures (click to open or close)
  1. Standard Specifications:
    Accuracy: ± 3% F.S.
    Repeatability: ± 1% F.S.
    Pressure Max.: 180 psig (12.6 kg/cm2)
    Pressure Min.: 10 psig (0.67 kg/cm2)
    Temp. Max.: 212ºF (100ºC)
    Temp. Min.: -30ºF (-34ºC)
    IP67 / NEMA 4X Rated Enclosure
  2. Electrical Rating:
    Power Input:
    100mA, 24Vdc power supply 20-30Vdc (Not Included)
    Input loop powered from 4-20mA signal. Voltage drop max. 2.6V
  3. Display:
    Rate Display:
    High intensity reflective numeric and alpha numeric LCD, UV resistant
    User definable, 8 times/sec - 30 secs.
    Password Protection
    7 and 11 digit various symbols and measuring units
  4. Environmental:
    Operating Temperature: -30ºF (-34ºC) to 212ºF (100ºC)
    Humidity: 0-90% Noncondensing
  5. Accuracy:
    0.5% F.S. (Non-linearity, Repeatability and Hysteresis
    Stability:
    0.5%F.S./year
  6. Signal Inputs:
    Full Scale Range: 4 to 20 mA DC
    Loop Voltage Drop: 2.6 Volts Max. at 20mA
    Update Time: 4 times/sec.
    Span: 0.001/999,999 with available decimal position
    16 Bit resolution, error < 0.01mA/+- 0.05% F.S.
    Low cutoff supplied to inhibit indications at low flow rates
  7. Signal Ouput:
    The pulse output transmitting accumulated total
    Type: one passive transistor output (NPN)
    Max. 500Hz pulse length user definable between 1 msec up to 10 sec.
  8. Calibration & Operation:
    Input Scaling: Via front keypad
    Decimal Point: Via front keypad
    Reset Input: Via front keypad
    Keypad: 3 tactile feedback keys
Click to openConstruction: (click to open or close)
Specifications Standard Optional
Housing Polycarbonate-UV Stabilized None
Body Bronze Monel - 316SS
Bellows Bronze Monel - 316SS - Inconel
Seals Buna-N Viton - EPR - Teflon
Crystal Polycarbonate None
Gear Movement Bronze 316SS
Accuracy ± 3% F.S. ± 3% F.S.
Repeatability ± 1% F.S. ± 1% F.S.
Pressure - Maximum 180psig 400psig
Pressure - Minimum 10psig 10psig
Temperature - Maximum 212° F 350° F
Temperature - Minimum -30° F -80° F
Click to openApplication Examples:: (click to open or close)
Cooling Systems
Monitor correct cooling flow to machinery. Protect valuable equipment by using a low flow switch to shut down machinery before damage. The Flo-GageTM will not foul with small debris frequently found in cooling systems. Fouling can cause typical flow switches to stick and fail to detect low flow conditions.
Lubrication Oil System
Flo-gages are ideal for measuring lube-oil. They do not require that the oil be transparent to be measured. Low flow switches can add additional protection.
Cutting Oil Systems
Proper flow of cutting oil is essential to machining operations. Automatic machines which run unattended require monitoring of the flow of cutting fluids. The gage allows quick setting of the proper flow rate. The low flow switch can stop machines before bad parts are produced or equipment damaged.